{"title":"Rumpf \u0026 Gelcoat mit THE FINISHER","description":null,"products":[{"product_id":"koch-chemie-the-finisher-marine-waxpolish-wachspolitur","title":"THE FINISHER “WaxPolish” wax polish","description":"\u003ch2\u003eTHE FINISHER × Koch-Chemie “WaxPolish” — wax polish for a rich gelcoat finish\u003c\/h2\u003e\n\u003cblockquote\u003e\n\u003cp\u003e\u003cem\u003eWhere does WaxPolish earn its keep on board? — This marine wax polish visibly lifts gelcoat and glossy paint, optically smooths light hazing and leaves an even, water-repellent wax film. Easy to buff off, holds up day-to-day, spot on after your post-trip wash.\u003c\/em\u003e\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003chr\u003e\n\u003cp\u003e\u003cstrong\u003eTHE FINISHER WaxPolish wax polish\u003c\/strong\u003e is your quick gloss-and-protection upgrade for boats: on smooth gelcoat and high-gloss paint it lays down a rich, calm depth of gloss and a thin-film, hydrophobic layer of protection. Perfect after a clean with CleanMarine or a bit of light polishing – as a stand-alone finish before the next trip out. It stays forgiving to apply, the look comes out even, and the surface feels clean and slick.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eRich depth of gloss on gelcoat: \u003c\/strong\u003eoptically smooths the finish, hides light hazing and lets water sheet off cleanly.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEasy handling:\u003c\/strong\u003e creamy to work, short flash-off, buffs off streak-free – even on bigger panels.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits the on-board system: \u003c\/strong\u003elay it down after CleanMarine\/polishing; boost the hydrophobics later with BodyGuard without wiping out the wax.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003ch3\u003eGelcoat wax polish – gloss, slickness \u0026amp; protection in one step\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eGelcoat wax polish\u003c\/strong\u003e means calming the surface optically while building a thin, protective film at the same time. THE FINISHER WaxPolish wax polish works as a finely tuned wax formula: mild cleaning agents pull away light oxidation haze, the polishing stage smooths the microstructure, the wax film flashes off evenly and drives beading\/sheeting. The result: a rich, deep look with no greasy sheen. On intact gelcoat one pass is often enough; where spots look visibly dull, sort them first with RoughCut\/FineCut or the one-step option PerfectOne – then WaxPolish seals the result.\u003c\/p\u003e\n\u003ch3\u003eApplication on board – prep, lay-down, buffing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eApplication\u003c\/strong\u003e starts with a clean base: wash the boat in the shade with CleanMarine, then dry it off. Lay THE FINISHER WaxPolish wax polish down thin on a soft pad\/cloth, spread it panel by panel in a cross pattern and let it flash off briefly. Once the film looks “clear”, buff it off with a fresh microfibre side, no pressure needed. On big surfaces work in sections and keep clear of edges and fittings. Don’t work it on hot surfaces or in full sun, and never let the product dry on. Keep it off plastics, non-slip decks, vinyl and textile parts – RubMarine, VinylGuard and TexLock\/CoverGuard have those covered.\u003c\/p\u003e\n\u003ch3\u003eDurability \u0026amp; care plan – combine your wax finish smartly\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eDurability \u0026amp; care plan\u003c\/strong\u003e come down to how you use the boat (sun, salt, time in the water). Keep up regular washes with CleanMarine and the finish stays visibly calmer, with dirt clinging less. Between washes you can top up the hydrophobics with BodyGuard without changing the wax look. Light water spots after rinsing come off with a clean cloth; treat heavier salt rings before the next wax round. When you feel the gloss dropping off: clean the surface, spot-polish if needed, then lay THE FINISHER WaxPolish wax polish on thin again and buff out – two lean passes beat one “heavy” coat.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003eCommon questions about THE FINISHER × Koch-Chemie “WaxPolish” — wax polish\u003c\/h2\u003e\n\u003ch4\u003eWhich surfaces do I use WaxPolish on?\u003c\/h4\u003e\n\u003cp\u003eSmooth gelcoat and high-gloss paint on board. Keep it off non-slip decks, dull gelcoat zones, vinyl, textile and plastic windows.\u003c\/p\u003e\n\u003ch4\u003eDo I have to polish first?\u003c\/h4\u003e\n\u003cp\u003eOnly on dull, weathered or noticeably scratched areas. Intact surfaces you can finish straight away with WaxPolish after the CleanMarine wash.\u003c\/p\u003e\n\u003ch4\u003eHow do I avoid streaks?\u003c\/h4\u003e\n\u003cp\u003eWork thin, in the shade, let it flash off briefly and buff off fully with a fresh microfibre side. Pick up any excess right away.\u003c\/p\u003e\n\u003ch4\u003eDoes WaxPolish play nice with BodyGuard?\u003c\/h4\u003e\n\u003cp\u003eYes. WaxPolish sets the optical base tone, BodyGuard tops up the hydrophobics later. Order: wax-based polish first, then spray protection (spaced out if needed).\u003c\/p\u003e\n\u003ch4\u003eHow often should I refresh it?\u003c\/h4\u003e\n\u003cp\u003eDepends on use. With regular washing one wax refresh per season is often enough; more often with lots of salt and sun. Top up thin, don’t “build” layers.\u003c\/p\u003e\n\u003chr\u003e\n\u003cp\u003e\u003csmall\u003eLast updated: 01.11.2025 — Author: Daniel (Detailing1)\u003c\/small\u003e\u003c\/p\u003e","brand":"Koch-Chemie × THE FINISHER","offers":[{"title":"250ml","offer_id":56301034242383,"sku":"D1-KCX-77101-250ML-01","price":13.59,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0800\/3272\/7375\/files\/77101-250ML-01_1.png?v=1778249520"},{"product_id":"koch-chemie-the-finisher-marine-finecut-schritt-2-politur","title":"THE FINISHER \"FineCut\" Step 2 Polish","description":"\u003ch2\u003eTHE FINISHER × Koch-Chemie \"FineCut\" — the step-2 polish for a clear, hologram-free finish\u003c\/h2\u003e\n\u003cblockquote\u003e\n\u003cp\u003e\u003cem\u003eWhat do I use FineCut for? — As a step-2 polish after the heavy cut, FineCut pulls out haze and holograms, visibly clears up the paint and sets up a high-gloss, clean finish ready for sealing – fast, low-dust and repeatable.\u003c\/em\u003e\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003chr\u003e\n\u003cp\u003e\u003cstrong\u003eTHE FINISHER FineCut step 2 polish\u003c\/strong\u003e is your precision refining step after defect correction. It lifts cut marks, grey haze and light swirls out of the clear coat, breaks down smoothly and leaves a calm, high-gloss look – the perfect bridge between the heavy correction stage (\u003cem\u003eRoughCut\u003c\/em\u003e) and the protection layer (\u003cem\u003eBodyGuard\u003c\/em\u003e or wax-based finishes). Day-to-day that means less rework, clean wipe-off and reliable results on common OEM clear coats – spot on for daily drivers, sales prep and \"clearing up\" after spot corrections.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eTargeted refining:\u003c\/strong\u003e pulls out holograms and cut haze, sharpens the reflections and gives you a calm, deep paint look.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEasy to work:\u003c\/strong\u003e long open time, low-dust matrix and easy buff-off – spot on for a dual-action workflow.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSystem logic:\u003c\/strong\u003e perfect after \u003cem\u003eRoughCut\u003c\/em\u003e, then protect (e.g. \u003cem\u003eBodyGuard\u003c\/em\u003e); for quick all-in-one jobs, \u003cem\u003ePowerSpeedPolish\u003c\/em\u003e is ready to go.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003ch3\u003eStep-2 polish – micro-abrasives, oil matrix \u0026amp; finish stability\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eStep-2 polish\u003c\/strong\u003e means controlled cut with a fine break-down. FineCut’s micro-abrasives grab the leftover defects from the cut, break down evenly and finish very fine. The moderately oily carrier matrix keeps the pad \"open\" for longer, cuts down on dry running and helps a streak-free wipe-off. The result is a clear, crisp gloss with no \"milky\" zones and clearly reduced holograms – the ideal base for any sealant. Because FineCut doesn’t leave heavy fillers sitting on top, the look stays put and doesn’t fall apart after the first wash.\u003c\/p\u003e\n\u003ch3\u003eAutomotive workflow – pad choice, pressure, cross-passes \u0026amp; buffing off\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eAutomotive workflow\u003c\/strong\u003e: after the pre-wash (TropicSnow), hand wash (MagicShampoo) and, if needed, a heavy step with RoughCut, you work panel by panel. Start with a medium-hard foam pad; switch to a soft finishing pad on sensitive, soft clear coats, and on hard-wearing paint a medium-firm foam can add bite. Prime the pad thin, 3–4 drops of product, spread on a low speed, then polish in even cross-passes with moderate pressure until the film goes visibly and noticeably \"thin\". At the end, ease off the pressure and stroke speed (\"jeweling\") to pull that last bit of gloss. Work edges and fresh paint gently, and keep off plastics or tape them off. Take residue off fully with a fresh, dense microfibre – the finish should look dry, clear and cloud-free. Then seal to suit the job: fast and hydrophobic with BodyGuard, classic deep gloss with ShineSpeedPolish as a wax-based finish, or a quick \"pop\" in between with JustPerfect.\u003c\/p\u003e\n\u003ch3\u003eCompatibility \u0026amp; limits – paint hardness, one-step alternative \u0026amp; protection\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eCompatibility \u0026amp; limits\u003c\/strong\u003e: FineCut works brilliantly on most OEM clear coats – on very hard paint it may want a longer set or a slightly more aggressive pad, and on very soft paint a gentle, short follow-up with a soft pad helps. When time is tight and you need defect removal \u003cem\u003eand\u003c\/em\u003e finish in one go, reach for \u003cem\u003ePowerSpeedPolish\u003c\/em\u003e as a one-step. If there are only fine wash marks and you want protection, \u003cem\u003eShineSpeedPolish\u003c\/em\u003e (a wax polish) is often enough. Don’t polish matte paint\/wraps or PPF – you’d change the matte level or gloss look without meaning to. After FineCut, a protection layer always goes on the clean finish: \u003cem\u003eBodyGuard\u003c\/em\u003e for hard-wearing water beading or, if you like, a waxy finish. Clean cloths, cool panels and shade are a must; if a pad dusts, it’s overloaded – blow it out or swap it.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003eCommon questions about THE FINISHER × Koch-Chemie \"FineCut\" — step 2 polish\u003c\/h2\u003e\n\u003ch4\u003eHow is FineCut different from RoughCut?\u003c\/h4\u003e\n\u003cp\u003eRoughCut is the heavy defect removal (step 1), FineCut refines afterwards: it takes out haze\/holograms and brings clarity to the look. The two build on each other.\u003c\/p\u003e\n\u003ch4\u003eDual-action or rotary?\u003c\/h4\u003e\n\u003cp\u003eA dual-action gives you the safest, hologram-free result. Only work with a rotary if you’re experienced, and settle the panel with a quick dual-action finishing pass.\u003c\/p\u003e\n\u003ch4\u003eDoes FineCut dust?\u003c\/h4\u003e\n\u003cp\u003eWith the right amount of product, cool panels and clean pads it stays low-dust. Dust usually comes from overloaded pads or too much heat – blow out\/swap pads regularly.\u003c\/p\u003e\n\u003ch4\u003eCan I seal straight after?\u003c\/h4\u003e\n\u003cp\u003eYes. Take residue off fully, then seal with BodyGuard or – if you like – set a waxy tone with ShineSpeedPolish\/WaxPolish.\u003c\/p\u003e\n\u003ch4\u003eIs it OK for gelcoat too?\u003c\/h4\u003e\n\u003cp\u003eSpot work yes, e.g. after heavier steps, but large gelcoat areas are quicker with PerfectOne (one-step), and then you lock them in with WaxPolish\/BodyGuard.\u003cem\u003e\u003c\/em\u003e\u003c\/p\u003e\n\u003chr\u003e\n\u003cp\u003e\u003csmall\u003eLast updated: 01.11.2025 — Author: Daniel (Detailing1)\u003c\/small\u003e\u003c\/p\u003e","brand":"Koch-Chemie × THE FINISHER","offers":[{"title":"250ml","offer_id":56301049971023,"sku":"D1-KCX-77102-250ML-01","price":15.29,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0800\/3272\/7375\/files\/77102-250ML-01_1.png?v=1778249523"},{"product_id":"koch-chemie-the-finisher-marine-perfectone-onesteppolitur","title":"THE FINISHER \"PerfectOne\" OneStepPolish","description":"\u003ch2\u003eTHE FINISHER × Koch-Chemie „PerfectOne“ — OneStepPolish for gelcoat gloss in a single pass\u003c\/h2\u003e\n\u003cblockquote\u003e\n\u003cp\u003e\u003cem\u003eWhy is PerfectOne ideal on board? — The one-step polish pulls dull oxidation haze and fine scratches out of gelcoat, finishes down low on holograms and lays down a deep, clear look in one go – the perfect base for WaxPolish or BodyGuard.\u003c\/em\u003e\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003chr\u003e\n\u003cp\u003e\u003cstrong\u003eTHE FINISHER PerfectOne OneStepPolish\u003c\/strong\u003e is our marine shortcut for smooth gelcoat and high-gloss painted surfaces on the boat. It pairs real cut with a safe finish, pulls out oxidation grey and wash haze and leaves a calm, deep look that wipes off easily. On big panels PerfectOne works long and low on dust – perfect for a large-throw dual-action. Once you’ve polished, you seal the result either the classic way with WaxPolish or hydrophobic with BodyGuard, depending on what you’re after.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eStrong one-step for gelcoat: \u003c\/strong\u003evisibly knocks back oxidation \u0026amp; fine scratches, gives a crisp mirror and a clean reflection.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSafe finishing:\u003c\/strong\u003e long open time, low-hologram finish, easy buff-off – workable on big boat panels.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWorkflow on board:\u003c\/strong\u003e polish after CleanMarine, then set WaxPolish (deep gloss) or BodyGuard (hydrophobic).\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003ch3\u003eOne-step polish for gelcoat – cut \u0026amp; finish in balance\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eOneStepPolish\u003c\/strong\u003e on gelcoat lives from the tuned interplay between micro-abrasives and a matrix that carries but never smears. PerfectOne gives you the bite you need up front to break chalky oxidation haze, then finishes down fine and pulls a clear, low-hologram look. Because gelcoat is thermally slow, that long open time works for you: you can work the product through cleanly without chasing residue in a hurry. What you get isn’t a masked shine but an optically settled, smooth surface – perfect for laying protection down evenly.\u003c\/p\u003e\n\u003ch3\u003eUse on board – prep, pad choice \u0026amp; machine work\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eUse\u003c\/strong\u003e starts with a clean base: wash the boat in the shade with CleanMarine and dry it, tape off sensitive edges\/fittings. For the main pass a medium foam pad on the dual-action (large throw) does the job – with more defects you can step up to a firmer pad in a controlled way, and go soft on sensitive areas. Set 3–4 pea-sized drops, spread on a low setting, then work in even crosshatches with moderate pressure until the film goes visibly thin and clear. To finish, ease off pressure\/passes („jeweling“) and wipe all residue off fully with fresh microfibre. Keep it off anti-slip decks, textile\/vinyl, polycarbonate\/acrylic windows and matte surfaces; avoid heated areas and full sun.\u003c\/p\u003e\n\u003ch3\u003eResult \u0026amp; care plan – protection choice, follow-up \u0026amp; limits\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eResult\u003c\/strong\u003e is a deep, calm gelcoat finish with real slickness under your hand. For seasonal and everyday protection you lay WaxPolish down straight after wiping (classic deep gloss) or go with BodyGuard for a hydrophobic, easy-to-refresh spray seal. Stubborn, deeper scratches or heavy chalking need a quick correction pass with RoughCut first; fine leftover haze after a heavy cut you pull away with FineCut and can run PerfectOne as a fast blending pass. Interim washes with CleanMarine hold the look; seeing gloss drop off? Clean the surface, test a spot, run PerfectOne again panel by panel – two lean passes beat one heavy coat.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003eCommon questions about THE FINISHER × Koch-Chemie „PerfectOne“ — OneStepPolish\u003c\/h2\u003e\n\u003ch4\u003eWhat surfaces do I use PerfectOne on?\u003c\/h4\u003e\n\u003cp\u003eOn smooth gelcoat and high-gloss marine painted surfaces. Don’t use it on anti-slip decks, matte surfaces, vinyl\/textile or plastic windows.\u003c\/p\u003e\n\u003ch4\u003eIs PerfectOne enough for heavy oxidation?\u003c\/h4\u003e\n\u003cp\u003eFor medium oxidation, yes. On heavily chalked gelcoat, run RoughCut first, then even it out with PerfectOne and seal.\u003c\/p\u003e\n\u003ch4\u003eDual-action or rotary?\u003c\/h4\u003e\n\u003cp\u003eA dual-action (large throw) gives the safest, lowest-hologram finish on big panels. Only go rotary if you’re experienced, and settle it with a short, gentle finishing pass.\u003c\/p\u003e\n\u003ch4\u003eDoes PerfectOne leave protection behind?\u003c\/h4\u003e\n\u003cp\u003eIt’s all about correction \u0026amp; finish. For durable everyday protection, put WaxPolish or BodyGuard on straight after.\u003c\/p\u003e\n\u003ch4\u003eDoes the polish dust?\u003c\/h4\u003e\n\u003cp\u003eWith fresh pads, a moderate amount of product and cool panels it stays low on dust. Overloaded pads or heat push more dust – blow out\/swap pads regularly.\u003c\/p\u003e\n\u003chr\u003e\n\u003cp\u003e\u003csmall\u003eLast updated: 01.11.2025 — Author: Daniel (Detailing1)\u003c\/small\u003e\u003c\/p\u003e","brand":"Koch-Chemie × THE FINISHER","offers":[{"title":"250ml","offer_id":56301061538127,"sku":"D1-KCX-77103-250ML-01","price":20.39,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0800\/3272\/7375\/files\/77103-250ML-01_1.png?v=1778249525"},{"product_id":"koch-chemie-the-finisher-marine-roughcut-schritt-1-politur","title":"THE FINISHER “RoughCut” Step 1 polish","description":"\u003ch2\u003eTHE FINISHER × Koch-Chemie “RoughCut” — Step 1 polish for fast, controlled defect removal\u003c\/h2\u003e\n\u003cblockquote\u003e\n\u003cp\u003e\u003cem\u003eWhen do I reach for RoughCut? — When you want to visibly pull wash marks, heavier swirls and sanding or oxidation haze out of the paint. This Step 1 polish gives you high cut with a long open time, a low-dust run, and sets the finish up perfectly for FineCut \u0026amp; protection.\u003c\/em\u003e\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003chr\u003e\n\u003cp\u003e\u003cstrong\u003eTHE FINISHER RoughCut Step 1 polish\u003c\/strong\u003e is our powerful way into paint correction: high defect removal, a smooth run, clean wipe-off. On common OEM clearcoats, \u003cstrong\u003eTHE FINISHER RoughCut Step 1 polish\u003c\/strong\u003e pulls grey haze and heavy wash marks out under control, without flooding the panel with dust. After the cut you clear the picture up with FineCut (step 2) and lock the work in with BodyGuard or a waxy finishing stage. That gives you a repeatable workflow from the first polishing pass to protection – fast, logical, safe. \u003cstrong\u003eTHE FINISHER RoughCut Step 1 polish\u003c\/strong\u003e reliably hands you the base for a crisp, low-hologram finish.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eHigh cut, controlled run: \u003c\/strong\u003epulls defects out visibly, long open time, clean wipe-off – ideal for DA workflows.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLow dust \u0026amp; efficient:\u003c\/strong\u003e reduced dusting with proper pad care; clear residue control for clean work.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSystem logic:\u003c\/strong\u003e polish after TropicSnow\/MagicShampoo, refine with FineCut and lock it in with BodyGuard or ShineSpeedPolish.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003ch3\u003eStep 1 polish – micro-abrasives, matrix \u0026amp; defect removal\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eStep 1 polish\u003c\/strong\u003e means: take substance off without fraying the finish. RoughCut’s micro-abrasives bite into defects quickly, spread evenly and “drive out” fine at the end. The load-bearing but non-greasy matrix keeps the pad open for a long time, minimises dry running and lets you use the whole work cycle instead of quitting early. The result: clear, defined paint with clearly reduced scratches and haze – ready to be refined with FineCut. Because the polish leaves no overdone fillers standing, the picture stays stable and doesn’t turn after the first wash.\u003c\/p\u003e\n\u003ch3\u003eAutomotive workflow – pad choice, pressure \u0026amp; cross-hatch in practice\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eAutomotive workflow\u003c\/strong\u003e starts with a clean base (TropicSnow → MagicShampoo). Start with a medium-hard foam pad; depending on paint hardness you can go firmer or softer. Prime the pad thin, put down 3–4 small drops, spread on a low setting, then work in even cross-hatch passes with moderate pressure until the film gets visibly thin. At the end, ease off pressure and stroke speed a touch to pull the panel “to clarity”. Work edges, fresh paint and sensitive zones gently, and mask off adjacent plastics. Take residues off fully with a dense microfibre. Now comes the step 2 pass with FineCut for gloss, depth and hologram safety; after that seal to your target look (BodyGuard for hydrophobicity, ShineSpeedPolish for waxy saturation or JustPerfect as a later pop booster).\u003c\/p\u003e\n\u003ch3\u003eLimits \u0026amp; alternatives – paint hardness, one-step \u0026amp; material choice\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eLimits \u0026amp; alternatives\u003c\/strong\u003e: very hard clearcoats allow longer sets or bitier pads; on soft\/unstable paints a gentle finishing pass reduces the risk of fresh haze. When time is tight and defect removal plus finish in one go is enough, PowerSpeedPolish is the one-step route; for only light marks ShineSpeedPolish does the job. Matte paints\/wraps and PPF stay off the table – polishing would change the matte level or the film look. Note: on gelcoat use it only in a targeted way and with experience; for large boat surfaces PerfectOne works more efficiently and with fewer holograms, and there you lock the finish in with WaxPolish or BodyGuard.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003eCommon questions about THE FINISHER × Koch-Chemie “RoughCut” — Step 1 polish\u003c\/h2\u003e\n\u003ch4\u003eHow is RoughCut different from FineCut?\u003c\/h4\u003e\n\u003cp\u003eRoughCut is the strong defect removal (step 1). FineCut refines afterwards: it takes out cut haze\/holograms and brings clarity and gloss into the picture.\u003c\/p\u003e\n\u003ch4\u003eDA or rotary?\u003c\/h4\u003e\n\u003cp\u003eA DA gives you the safest, low-hologram result. Only work with a rotary if you’re experienced, and calm the surface afterwards with a short DA finishing pass.\u003c\/p\u003e\n\u003ch4\u003eDoes RoughCut dust?\u003c\/h4\u003e\n\u003cp\u003eWith fresh pads, a moderate amount of product and cool panels it stays low-dust. Dust usually comes from overloaded pads, heat or too-long dry runs.\u003c\/p\u003e\n\u003ch4\u003eDoes RoughCut remove sanding marks?\u003c\/h4\u003e\n\u003cp\u003eYes, light to medium sanding marks and heavy wash swirls get visibly reduced. For the final picture FineCut always follows as step 2.\u003c\/p\u003e\n\u003ch4\u003eWhat comes after RoughCut?\u003c\/h4\u003e\n\u003cp\u003eDegreasing the panel isn’t necessary; take residues off fully, then FineCut for gloss\/clarity. Finally seal with BodyGuard or set a waxy finish.\u003c\/p\u003e\n\u003chr\u003e\n\u003cp\u003e\u003csmall\u003eLast updated: 01.11.2025 — Author: Daniel (Detailing1)\u003c\/small\u003e\u003c\/p\u003e","brand":"Koch-Chemie × THE FINISHER","offers":[{"title":"250ml","offer_id":56301092176207,"sku":"D1-KCX-77104-250ML-01","price":21.24,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0800\/3272\/7375\/files\/77104-250ML-01_1.png?v=1778249528"},{"product_id":"koch-chemie-the-finisher-marine-bodyguard-spruhversiegelung","title":"THE FINISHER \"BodyGuard\" Spray Sealant","description":"\u003ch2\u003eTHE FINISHER × Koch-Chemie „BodyGuard“ — Spray Sealant (Marine) for gelcoat slickness \u0026amp; strong beading\u003c\/h2\u003e\n\u003cblockquote\u003e\n\u003cp\u003e\u003cem\u003eWhat do I use BodyGuard for on board? — This marine spray sealant lays down a hydrophobic, even protective film on gelcoat and glossy painted surfaces in minutes, visibly cuts how hard salt clings, adds slickness and makes the next wash quicker – as a drying aid or on a dry surface.\u003c\/em\u003e\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003chr\u003e\n\u003cp\u003e\u003cstrong\u003eTHE FINISHER BodyGuard Spray Sealant\u003c\/strong\u003e is your fast protection-and-slickness step after the wash. On smooth gelcoat and high-gloss marine-painted panels it builds a thin, even layer of protection: water sheets off cleanly, salt and spray cling less, and the surface feels „dry-slick“. Ideal as a drying aid straight after \u003cem\u003eCleanMarine\u003c\/em\u003e, or as a quick finish on a dry surface. Keep it off non-skid, teak, vinyl or plastic windows – those stay the job of dedicated deck and material products.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eHydrophobic in minutes: strong beading\/sheeting, noticeably slicker run-off – you can feel the salt and grime clinging less.\u003c\/li\u003e\n\u003cli\u003eEasy \u0026amp; streak-free: thin, even flash-off; works as a drying aid or a dry finish.\u003c\/li\u003e\n\u003cli\u003eFits the marine system: sits behind CleanMarine and over PerfectOne\/WaxPolish – top up the protection without any „layer build-up“.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003ch3\u003eSpray sealant for your boat – hydrophobicity, slickness \u0026amp; salt resistance\u003c\/h3\u003e\n\u003cp\u003eA \u003cstrong\u003espray sealant\u003c\/strong\u003e on gelcoat needs two things: thin polymers that sit flat and evenly, and a controlled flash-off. BodyGuard builds exactly that kind of film: it smooths out the micro-texture, gets water beading off cleanly and cuts how much salt, spray and harbour film grab the surface. The result isn’t „oily“, it’s dry and quiet – perfect when you want a clear, easy-to-rinse surface again fast after a sail. Because the layer is fine, the reflection stays crisp; at the same time dirt walks off quicker when you rinse, which takes the load off your care intervals.\u003c\/p\u003e\n\u003ch3\u003eUse on board – drying aid or dry finish\u003c\/h3\u003e\n\u003cp\u003eAlways \u003cstrong\u003eapply\u003c\/strong\u003e in the shade on a cool surface. After the CleanMarine wash, rinse down generously with fresh water. \u003cem\u003eDrying aid:\u003c\/em\u003e 1–2 spritzes per section onto the wet panel or into the drying towel, pull off the water, then go over it streak-free with a fresh microfibre side. \u003cem\u003eDry finish:\u003c\/em\u003e use two towels (one to spread, one to buff off) and work panel by panel without pressure. Take off any excess straight away, never let the product dry on. \u003cstrong\u003eNo-go:\u003c\/strong\u003e non-skid decks, teak, vinyl upholstery, polycarbonate\/acrylic windows – they end up slippery or smeary. Give fittings and edges a quick dry wipe after any contact.\u003c\/p\u003e\n\u003ch3\u003eCare plan \u0026amp; compatibility – pairing with WaxPolish\/PerfectOne\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003ecare plan\u003c\/strong\u003e: after the main wash with CleanMarine, BodyGuard sets the everyday protection tone for the hull and smooth deck areas. You can run BodyGuard on its own, or lay it over an optical finish: \u003cem\u003ePerfectOne\u003c\/em\u003e (one-step on gelcoat) → BodyGuard for hydrophobicity; or \u003cem\u003eWaxPolish\u003c\/em\u003e for classic deep gloss → BodyGuard later as a quick hydrophobicity booster. Depending on sun, salt and time in the water, top it up in minutes every few weeks. When the beading starts to fade: wash, lay a thin coat back on – no thick layers, no „gunking it up“.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003eCommon questions about THE FINISHER × Koch-Chemie „BodyGuard“ — Spray Sealant (Marine)\u003c\/h2\u003e\n\u003ch4\u003eWhich surfaces is it for?\u003c\/h4\u003e\n\u003cp\u003eOn smooth gelcoat, high-gloss marine paint and smooth plastics. Not on non-skid, teak, vinyl or plastic windows.\u003c\/p\u003e\n\u003ch4\u003eDrying aid or dry – which is better?\u003c\/h4\u003e\n\u003cp\u003eBoth work. As a drying aid it cuts friction while you dry off; dry application gets you the „quietest“ finish. Decide by your time and the look you’re after.\u003c\/p\u003e\n\u003ch4\u003eDoes BodyGuard play nicely with WaxPolish?\u003c\/h4\u003e\n\u003cp\u003eYes. Top BodyGuard over WaxPolish later on to boost the hydrophobicity without painting over the wax look.\u003c\/p\u003e\n\u003ch4\u003eHow often should I top it up?\u003c\/h4\u003e\n\u003cp\u003eEvery few weeks, depending on use. After salty legs or a long stretch in the water, just lay a thin coat back on after the wash.\u003c\/p\u003e\n\u003ch4\u003eSeal the windows \u0026amp; vinyl too?\u003c\/h4\u003e\n\u003cp\u003eNo. Clean windows separately with SeaYou, clean vinyl with VinylTexClean and protect it with VinylGuard. That keeps the feel and look right for each material.\u003c\/p\u003e\n\u003chr\u003e\n\u003cp\u003e\u003csmall\u003eLast updated: 01.11.2025 — Author: Daniel (Detailing1)\u003c\/small\u003e\u003c\/p\u003e","brand":"Koch-Chemie × THE FINISHER","offers":[{"title":"1000 ml \/ 1 liter","offer_id":56301331022159,"sku":"D1-KCX-77113-1L-01","price":33.14,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0800\/3272\/7375\/files\/77113-1L-01_1.png?v=1778249533"},{"product_id":"koch-chemie-the-finisher-marine-hellowhite-antigilb","title":"THE FINISHER \"HelloWhite\" AntiGilb","description":"\u003ch2\u003eTHE FINISHER × Koch-Chemie „HelloWhite“ — AntiGilb for clean waterlines \u0026amp; fresh whites\u003c\/h2\u003e\n\u003cblockquote\u003e\n\u003cp\u003e\u003cem\u003eHow does HelloWhite work? — The AntiGilb chemically loosens waterline yellowing and light rust\/harbour film, brings the white back to gelcoat and glossy painted surfaces, rinses off neutral, and works as a targeted intermediate step before you protect with WaxPolish or BodyGuard.\u003c\/em\u003e\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003chr\u003e\n\u003cp\u003e\u003cstrong\u003eTHE FINISHER HelloWhite AntiGilb\u003c\/strong\u003e is your targeted stain remover against gelcoat yellowing at the waterline, bow, transom and around fittings. The active, controlled-flash formula softens organic „Tea-Stains“ and light metal\/harbour film so you can rinse them off without harsh mechanics. After treatment the surface looks visibly fresher and makes the ideal base for a wax- or spray-based finish. In the system, \u003cstrong\u003eTHE FINISHER HelloWhite AntiGilb\u003c\/strong\u003e sits between the main wash (CleanMarine) and protection (WaxPolish\/BodyGuard) – right where gelcoat shows those yellowed shadows.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eTargeted de-yellowing:\u003c\/strong\u003e loosens waterline yellowing and light rust\/harbour film in a controlled way – no sanding marathons and no grey afterimage.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eClean handling:\u003c\/strong\u003e wets evenly, works in fast, rinses off neutral; ideal for spot areas instead of „all or nothing“.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMarine system fit:\u003c\/strong\u003e use after CleanMarine, then lock it in with WaxPolish (deep gloss) or BodyGuard (hydrophobicity).\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003ch3\u003eAntiGilb – cause, how it works \u0026amp; reading the material\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eAntiGilb\u003c\/strong\u003e tackles the typical gelcoat yellowing („Tea-Stains“) that comes from salts, organic residue and light metal traces. THE FINISHER HelloWhite AntiGilb carries in active ingredients with strong wetting, chemically loosens the discolouring layer and makes it lift off with water. Because the formula flashes off in a controlled way, you work fast, on target, and without dried-on edges. It suits smooth gelcoat and high-gloss marine-painted panels; keep it off Non-Skid, vinyl, teak and polycarbonate\/acrylic windows so each material keeps the right feel and look.\u003c\/p\u003e\n\u003ch3\u003eOn-board use – waterline, fittings \u0026amp; transom\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eUse\u003c\/strong\u003e starts with a clean base: wash the boat in the shade with CleanMarine and rinse with fresh water. Spray HelloWhite onto the wet surface section by section from bottom to top, or apply with a pad, let it dwell 1–3 minutes (don't let it dry), agitate lightly with a soft pad\/brush if needed, then rinse generously with fresh water. Around metal fittings, drain edges and trailer bunks work quickly and take off any excess straight away. After that a short re-wash\/rinse is worth it so the pH is back to neutral – now the surface is ready for WaxPolish or BodyGuard.\u003c\/p\u003e\n\u003ch3\u003eResult, limits \u0026amp; building protection\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eResult\u003c\/strong\u003e is a visibly brightened, even white\/light surface with no yellow shadows – ideal „before protection“. Limits: deep oxidation, hard deposits and older, dark-brown waterlines need polishing first (PerfectOne) or local sanding by pros. After HelloWhite, saturate the look with WaxPolish or lock it in hydrophobic with BodyGuard; regular washes with CleanMarine stop it building back up fast. For vinyl upholstery, VinylTexClean\/VinylGuard stays in charge, windows are SeaYou's job – that keeps the care plan cleanly split and repeatable.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003eCommon questions about THE FINISHER × Koch-Chemie „HelloWhite“ — AntiGilb\u003c\/h2\u003e\n\u003ch4\u003eWhich surfaces do I use HelloWhite on?\u003c\/h4\u003e\n\u003cp\u003eOn smooth gelcoat and glossy marine-painted panels at the waterline, bow, transom. Don't use it on Non-Skid, teak, vinyl or plastic windows.\u003c\/p\u003e\n\u003ch4\u003eHow long should it dwell?\u003c\/h4\u003e\n\u003cp\u003e1–3 minutes in the shade. Don't let the product dry; in the heat work shorter and re-mist if needed. Always rinse generously with fresh water afterwards.\u003c\/p\u003e\n\u003ch4\u003eDo I have to neutralise?\u003c\/h4\u003e\n\u003cp\u003eA thorough rinse and a short re-wash with CleanMarine are enough. Rinse cloths\/pads out with fresh water afterwards.\u003c\/p\u003e\n\u003ch4\u003eDoes HelloWhite remove rust spots too?\u003c\/h4\u003e\n\u003cp\u003eLight rust shadows, yes. Deep pitting or rust speckle need a careful polish (e.g. PerfectOne) or specialised treatment depending on the material.\u003c\/p\u003e\n\u003ch4\u003eWhat's the right order?\u003c\/h4\u003e\n\u003cp\u003eWash with CleanMarine → spot-de-yellow with HelloWhite → rinse\/re-wash → WaxPolish (deep gloss) or BodyGuard (hydrophobicity). Treat windows\/vinyl separately.\u003c\/p\u003e\n\u003chr\u003e\n\u003cp\u003e\u003csmall\u003eLast updated: 01.11.2025 — Author: Daniel (Detailing1)\u003c\/small\u003e\u003c\/p\u003e","brand":"Koch-Chemie × THE FINISHER","offers":[{"title":"1000 ml \/ 1 liter","offer_id":56304256221519,"sku":"D1-KCX-77110-1L-01","price":40.79,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0800\/3272\/7375\/files\/77110-1L-01_1.png?v=1778249534"}],"url":"https:\/\/detailing1.nl\/en\/collections\/the-finisher-bootsbereich-rumpf.oembed","provider":"Detailing1","version":"1.0","type":"link"}